Elite access systems Miracle-One Spezifikationen Seite 1

TABLE OF CONTENTS…………………………………………………………UL LISTINGS AND INSTRUCTIONS……………………………………………WARNINGS AND PRECAUTIONS………………………………………………PROCEDURE FOR INSTALLATI

PR O C E D U R E F O R IN S TA L L AT I O N ( c o nt . )P L A C E M E N T O F M I RA C L E • 1 O N G AT EFor strength purposes, the front

P RO C E D U R E F O R I NS TA L L AT I O N (c o n t. )STEP 11: Re-install the cover.(REFER TO STEP 1)STEP 10: Adjust the traveling distancewith

R EM O V I N G T HE C O NT RO L B O AR DDetach the J1 and J3 plug .MO U N T I N G T H E CO N T R O L BO XRemove the three, phillips hea

CO N N E C T IN G P O W E RCAUTION: Do not over-bend the wire connec-tion from the operator. To do so will cause thewires to eventually break.PROPER

C ON N E C T I N G PO W E R M a s t e r / S l av ePROPER GROUNDING IS IMPORTANTIMPORTANT: Be sure to installthe Flex Connector (supplied) tosec

C HO O S I N G MO V E M E N T D I R E C T I O NSwitch the “Open Inside / Open Outside” switch on the control board to thecorresponding position for

P O W E R S UP P LYUse the plug-in transformer (sold by Elite Access System only) by hooking it upto 115V and use Two Conductor, low voltage, 14 gau

D R Y C O NTA CT & R E C E I V E R WI R I N GBACK TO TABLE OF CONTENTS

SA F E T Y & C E N T E R L O O P I N STA L L AT I O NBACK TO TABLE OF CONTENTS

PH O T O C E LL I N S TA L L AT I O NTo reduce the risk of injury, Elite H I G H LY RECOMMENDS installing a PHOTOCELL SENSORwhen the gate opens to l

U L L I STINGS AND I N S TR U C T I O NSINSTALLATION INSTRUCTIONS REGARDING THE GATE OPERATORA) Install the gate operator only when:1) The operat

CO N T R O L BO A R D D E S C R IP T IO N1. Open or Close Relay LED2. Control Relay LED3. Motor Fuse4. J1-Batteries and Motor Connector 5. Strike

C ON T R O L B OA R D DE SC R I PT I ON Ma st e r / S l a v e1. Open or Close Relay LED2. Control Relay LED3. Motor Fuse 4. J1-Batteries and

MA G L O C K & AL A R M CO N N E CT O R SUse the harness provided with theunit to make your connections tothese alarm outputs.Contact DataCo

B U R G L A R A L A R M ...HOUSE ALARMALARM SENSOR OUTPUTThe Alarm Sensor Output will close a circuitas an indication of possible events:• Heavy Gat

G AT E O PE N IN G I NS I DE I N STA L L ATI O N O F. . . NOTE:The optional relay harness, allowing interface with externaldevices, is availa

G ATE O PE N IN G O U TS I D E I N STA L L AT I O N O F. . .NOTE:The optional relay harness, allowing interface with externaldevices, is av

E M E R G E N C Y K EY R EL EA S ETo move the gate during an emergencyor power failure, insert the key (step 1)into the key release hole on the fr

CL O S E D E L AY O P T IO N(M a s t e r / S l a v e o n l y)This option is to be used when there is an master/slave installation with overl

CL O S E D E LAY O P T I ON( Ma s te r / S la v e on l y )This option is to be used when there is an master/slave installation with overlappin

T R O U B L E S H O O T I N GCheck the fusesIf the gate is not moving in any direction be sure to check all of the LED displays on the control board.

U L L I S T INGS A ND I N S TRUCT I O NSH) For a gate operator utilizing a non-contact sensor such as a photo beam:1) See instructions on the

T R O U B L E S H O O T I N GYou will see the alarm sensor LED on whenChecking Control Options (example - Radio Receiver)Problem:The radio receiver LE

MI R A C L E • 1 PA R TS L I S T1 - Control Board Screws (Set) Q0062 - Control Board Q222, Q2233A - Backup Batteries A BT MIR3B - Battery Rack3C -

MECHANICAL SPECIFICATIONSMOTOR - 24V DC, 12 Amps.CYCLES - 100 / Day.SHIPPING WEIGHT:Single Unit: 58 lbs. - Master/Slave: 89 lbsTORQUE - 600 lbs. of to

U L L I STIN G S AND I N STR U C T I ONSIMPORTANT SAFETY INSTRUCTIONSWARNING - To reduce the risk of injury or death:1. READ AND FOLLOW ALL INSTR

U L L I S T I N GS AN D I N ST R U C T I O NSGate – A moving barrier such as a swinging, sliding, raising lowering, rolling, or like,

WA R NI NG S AN D PR E CA U T I O N SIf the timer is to be left in the “on” position, thenadd a safety loop andcenter loop.Do not install upside d

PR O C E D U RE F O R IN S TA L L AT I O NOp e n To T h e I n s i deIndexingonCentralHoleIndexing onMounting Hole25.75”7.75”90°/105°6”10.5”8

PR O CE D U R E F O R I N S TA L L AT I O NOp e n To T h e O u t s id eIndexing onCentral HoleIndexing onMountingHoleBACK TO TABLE OF CONTEN

STEP 2: Release the mechanical lock byturning Key - F - to the horizontal position.P RO C E D U R E F OR I N S TA L L AT I O N ( c on t . ) STEP